Fujitsu XG0224 User Manual Download Page 601

Page: 601 / 631

XG Series User's Guide

Appendix

List of MIBs

601

List of MIBs

This appendix lists the MIBs supported by the device.

B.1

Standard MIB Definitions

The following shows meaning of MIB ACCESS column.

:MIB can be read only.

:MIB can be read and written.

–

:MIB can not be accessed.

B.1.1

system Group

*) Written MIB works on until reset.

B.1.2

interfaces Group

Available

Model

All models

No.

Name

Object identifier

MIB ACCESS

sysDescr

system.1

sysObjectID

system.2

sysUpTime

system.3

sysContact

system.4

RW (*)

sysName

system.5

RW (*)

sysLocation

system.6

RW (*)

sysServices

system.7

No.

Name

Object identifier

MIB ACCESS

ifNumber

interfaces.1

ifTable

interfaces.2

–

ifEntry

ifTable.1

–

ifIndex

ifEntry.1

ifDescr

ifEntry.2

ifType

ifEntry.3

ifMtu

ifEntry.4

ifSpeed

ifEntry.5

ifPhysAddress

ifEntry.6

ifAdminStatus

ifEntry.7

ifOperStatus

ifEntry.8

ifLastChange

ifEntry.9

ifInOctets

ifEntry.10

ifInUcastPkts

ifEntry.11

ifInNUcastPkts

ifEntry.12

ifInDiscards

ifEntry.13

ifInErrors

ifEntry.14

ifInUnknownProtos

ifEntry.15

ifOutOctets

ifEntry.16

ifOutUcastPkts

ifEntry.17

ifOutNUcastPkts

ifEntry.18

ifOutDiscards

ifEntry.19

ifOutErrors

ifEntry.20

ifOutQLen

ifEntry.21

ifSpecific

ifEntry.22

Summary of Contents for XG0224
























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for XG0224

Reviews:

Related manuals for XG0224

Brands by name

Popular brands

Fujitsu XG0224, User Manual

Search results

Summary of Contents for XG0224

Reviews:

Related manuals for XG0224

Brands by name

Popular brands