Fujitsu XG0224 User Manual Download Page 432 | Manualshive

Page: 432 / 631

background image

XG Series User's Guide

Chapter 5 Command Reference

USB connection Counter, Log, Statistics, and Status Display and Clear

Operation Commands

432

5.21.1.2 show usb storage status

Function

Displays USB mass storage controller status.

Available Model

XG0448 / XG0440DC / XG0440DCR / XG2600

Syntax

show usb storage status

Options

N/A

Use Mode

Operation mode (user class /admin class/CE class)
Configuration mode (admin class/CE class)

Explanation

Displays current status for USB mass storage controller.

Default

1)

USB mass storage controller thread status

Status is displayed via the following messages:
Uninit: not initialized
Waiting for USBD active
Waiting for entry class completed
Active
The information below is displayed only when a connected USB device has
been detected.

# show usb storage status

[Thread]

Status :

Active

---(1)

[Device #1]

Status :

Idle

---(2)

Speed :

Full

---(3)

Geometry probing

: Success

---(4)

Test unit ready

: Success

---(5)

Inquiry

: Success

Mode sense

: Success

Read capacity

: Success

Read format capacities : ----

Hold data

: Not exist

---(6)

Error status

: Get device specs [5/5] (Read format capacities) ---(7)

Error reason

: Transfer URB failure

---(8)

Error event

: 0x3200000d

---(9)

Request sense code

: (02, 10, 00)

---(10)

[Storage specs]

Vendor :

FUJITSU

---(11)

Product :

USB

PortableDrive

---(12)

Product Rev.

: 3.96

---(13)

Total sectors

: 500400

---(14)

Cylinders :

695

---(15)

Heads :

15

---(16)

Sectors per track

: 48

---(17)

[USB specs]

Speed :

Full

---(18)

Max LUN

: 3

---(19)

[USB configuration]

Device address

: 1

---(20)

Interface :

0

---(21)

Sub class

: 6

---(22)

LUN :

0

---(23)

BulkInEP :

0x82

---(24)

BulkOutEP :

0x02

---(25)

«
...
430
431
432
433
434
...
»

Summary of Contents for XG0224
























































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XG0224

Verizon DSL-2750B

Brand: D-Link Pages: 2

Brand: D-Link Pages: 4

Brand: Parker Pages: 344

Brand: D-Link Pages: 176

Brand: TP-Link Pages: 73

DG834GT - 108 Mbps Super G Wireless ADSL Router

Brand: NETGEAR Pages: 2

Brand: HARTING Pages: 13

Brand: ZKTeco Pages: 68

Brand: ZyXEL Communications Pages: 8

Brand: Planet Pages: 20

Cyclades CS4008

Brand: Avocent Pages: 2

Brand: Baileigh Pages: 20

Brand: Tripp Lite Pages: 2

Network Expansion Port 2

Brand: Navico Pages: 17

Modem/Router ADSL BIPAC-7100

Brand: Billion Pages: 13

Brand: NetApp Pages: 121

Brand: Honeywell Pages: 29

Brand: Honeywell Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands