manualshive.com logo in svg

Fujitsu Streamer DAT 160, User Manual, Page: 37 / 41

Share
Download
Fujitsu Streamer DAT 160 User Manual Download Page 37

36

  

 DAT 

160 

USB

Problems with cartridges

Troubleshooting

6.4.2

The drive will not accept the cartridge (or ejects it 
immediately)

The cartridge may have been damaged, for example dropped, or the drive may 
have a fault. If it is a cleaning cartridge, it has probably expired and should be 
discarded immediately.

For data cartridges:

Check that the drive has power (the power cable is properly connected and the 
Tape LED is on).

Ê

Check that you are using the correct media for the tape drive, see 

“Use the 

correct media” on page 23

.

Ê

Make sure that you have loaded the cartridge with the correct orientation. 

Ê

Check for damage to your media and discard it if it is damaged.

Ê

Use a new or known-good piece of media and see if it loads. If it does, the 
original cartridge is faulty and should be discarded.

Ê

Check if another DAT drive of the same model will accept the cartridge. If it 
does, the original drive may be faulty

Summary of Contents for Streamer DAT 160










































Reviews:

No comments