manualshive.com logo in svg

Fujitsu PRIMERGY TX300, Operating Manual, Page: 85 / 127

Share
Download
Fujitsu PRIMERGY TX300 Operating Manual Download Page 85

A26361-K881-Z102-4-7619

 79

8

Hot-plug/hot-swap Components

This chapter describes how to handle hot plug or hot swap components and/or 
how to modify your server hardware.

The hot swap procedure increases the availability of the system operation and 
guarantees a high degree of data integrity and fail-safe performance.

I

Upgrades or replacements of permanently installed components are 
described in the Service Manual and may only be performed by Service 
staff.

8.1

Hot-swap Power Supply Units

I

A redundant power supply can be created by installing a second hot-
swap wide range power supply unit. If one power supply unit fails, the 
other unit ensures operation can continue uninterrupted. The defective 
power supply unit can be replaced online.

V

CAUTION!

Please observe the safety information in chapter “Important Notes” on 
page 13.

8.1.1

Adding a hot-swap Power Supply Unit

The mounting location for the second hot-swap power supply unit contains a 
dummy module. This dummy module must be removed before installing a 
second power supply unit.

Ê

Open the two fixing screws and remove the dummy module from the second 
power supply unit mounting location.

V

CAUTION!

Keep the dummy module for future use. If the power supply unit is 
removed and not replaced with a new unit, the dummy must be 
reinstalled due to cooling, to comply with applicable EMC regulations 
(regulations on electromagnetic compatibility) and to protect against 
fire.

Ê

Open the transport lock of the second power supply unit, insert and lock it in 
the free location (see section “Replacing a Hot-swap Power Supply Unit” on 
page 80) and connect it to the line voltage (see section “Connecting the 
Server to the Line Voltage” on page 51).

Summary of Contents for PRIMERGY TX300
































































































































Reviews:

No comments