Fujitsu PRIMERGY TX2550 M5 Operating Manual Download Page 97

Page: 97 / 106

TX2550 M5

Operating Manual

Technical data

This section explains the specifications for the server. The specifications for this
server are liable to be updated without any notice. Please be forewarned.

The data sheets for this server contain more technical data. The data
sheets are available online at:

http://www.fujitsu.com/fts/products/computing/servers/primergy

For more information, see the

Documents

tab under e.g.

Rack Servers

For Japan:

http://www.fujitsu.com/jp/products/computing/servers/primergy

System board

Memory modules configuration

System board type

D3386

Chipset

Intel

C624 series

Processor (CPU)
CPU quantity and type 1 or 2 Intel® Xeon® CPUs (Platinum, Gold, Silver,

Bronze)

Memory slots

12 (6 DIMMs per CPU, 1 DIMM per channel)

Memory types

RDIMM/LRDIMM (DDR4)

NVM/LRDIMM

Memory capacity
(min. - max.)

8 GB - 1536 GB

Memory protection

Memory Scrubbing; SDDC (only for registered
DIMMs); Hot-spare memory support; Memory
Mirroring support

Memory notes

RDIMM/LRDIMM: 2933 MHz memory modules with
8, 16, 32, or 64 GB

NVM/LRDIMM: 2666 MHz memory modules with
128, 256, or 512 GB

Summary of Contents for PRIMERGY TX2550 M5











































































































Search results

Summary of Contents for PRIMERGY TX2550 M5

Reviews:

Related manuals for PRIMERGY TX2550 M5

Brands by name

Popular brands

Fujitsu PRIMERGY TX2550 M5, Operating Manual

Search results

Summary of Contents for PRIMERGY TX2550 M5

Reviews:

Related manuals for PRIMERGY TX2550 M5

Brands by name

Popular brands