Fujitsu PRIMERGY TX2550 M5 Operating Manual Download Page 33

Page: 33 / 106

TX2550 M5

Operating Manual

Product description

iRMC-related status signals

HDD/SSD prefailure detection

Depending on your hardware configuration HDD/SSD prefailure detection will
be supported.

The requirements are:

– iRMC S5 Firmware 1.2 or later

– supported OOB RAID system

ID indicator

Global error
indicator

Description

flashing blue

off

A remote connection has been
established. Local VGA output has been
disabled during the remote session.

flashing blue

flashing orange

An emergency flash of the iRMC firmware
is in progress.

For more information on the
emergency flash of the iRMC
firmware, see the "FUJITSU Server
PRIMERGY TX2550 M5 Upgrade
and Maintenance Manual".

Summary of Contents for PRIMERGY TX2550 M5











































































































Search results

Summary of Contents for PRIMERGY TX2550 M5

Reviews:

Related manuals for PRIMERGY TX2550 M5

Brands by name

Popular brands

Fujitsu PRIMERGY TX2550 M5, Operating Manual

Search results

Summary of Contents for PRIMERGY TX2550 M5

Reviews:

Related manuals for PRIMERGY TX2550 M5

Brands by name

Popular brands