Fujitsu PRIMERGY TX1330 M4 Operating Manual Download Page 34

Page: 34 / 110

Operating Manual

TX1330 M4

Product description

iRMC-related status signals

HDD/SSD prefailure detection

Depending on your hardware configuration HDD/SSD prefailure detection will
be supported.

The requirements are:

– iRMC S5 Firmware 1.2 or later

– supported OOB RAID system

ID indicator

Global error
indicator

Description

flashing blue

off

A remote connection has been
established. Local VGA output has been
disabled during the remote session.

flashing blue

flashing orange

An emergency flash of the iRMC firmware
is in progress.

For more information on the
emergency flash of the iRMC
firmware, see the "FUJITSU Server
PRIMERGY TX1330 M4 Upgrade
and Maintenance Manual".

Summary of Contents for PRIMERGY TX1330 M4















































































































Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands

Fujitsu PRIMERGY TX1330 M4, Operating Manual

Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands