Fujitsu PRIMERGY TX1330 M2 Operating Manual Download Page 74 | Manualshive

Page: 74 / 86

background image

74

Operating Manual

TX1330 M2

Starting up and operation

6.4.2

Configuring the SAS/SATA RAID controller
(PCIe expansion card)

The server has a SAS/SATA RAID controller with "MegaRAID functionality". You
can configure the SAS/SATA RAID controller either before or during installation
with the ServerView Installation Manager. Using the ServerView Installation
Manager is recommended.

I

A separate utility is available to the controller for MegaRAID
configuration. For further information, refer to the "LSI MegaRAID SAS
Software User Guide" (on the Fujitsu manuals server under

x86 Servers

-

Expansion Cards

-

Storage Adapters

-

LSI Configuration Software

).

Further information on modular RAID controllers is provided in the
"Modular RAID Controller Installation Guide" (on the Fujitsu manuals
server under

x86 Servers

-

Expansion Cards

-

Storage Adapters

-

LSI SAS /

SCSI RAID Controllers

).

I

Descriptions of operating systems not covered in the controller manual
are provided in the corresponding readme under:

http://www.fujitsu.com/global/services/computing/server/ia/driver/index.html

(for the global market).

http://jp.fujitsu.com/platform/server/primergy/downloads/

(for the Japanese market).

«
...
72
73
74
75
76
...
»

Summary of Contents for PRIMERGY TX1330 M2























































































Reviews:

No comments

Related manuals for PRIMERGY TX1330 M2

Brand: IBM Pages: 54

Brand: IBM Pages: 214

Express5800/320Fa-L

Brand: NEC Pages: 406

Brand: IBM Pages: 220

SUPERSERVER 5019S-M

Brand: Supermicro Pages: 65

Brand: SmartSight Pages: 113

Brand: IOGear Pages: 44

TVS- 72XU Series

Brand: QNAP Pages: 56

SPARC T8 Series

Brand: Oracle Pages: 12

Brand: Polycom Pages: 2

Brand: Gigabyte Pages: 108

NETWORK SATELLITE 5.0.0 -

Brand: Red Hat Pages: 84

ProxyServer MTPSR1-202ST

Brand: Multitech Pages: 142

SUPERSERVER 6026TT-IBQF

Brand: Supermicro Pages: 100

SuperServer 510P-WT

Brand: Supermicro Pages: 113

SuperWorkstation 7049GP-TRT

Brand: Supermicro Pages: 133

Brand: Inspur Pages: 37

Brand: Vlinx Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands