Fujitsu PRIMERGY TX1330 M2 Operating Manual Download Page 62

Page: 62 / 86

Operating Manual

TX1330 M2

Starting up and operation

6.2.1.2

Indicators on the control panel

Pos. Indicator

Status

Description

ID indicator

blue on

server has been highlighted using
ServerView Operations Manager, iRMC
web frontend or the ID button on the
front panel for easy identification

blue
flashing

server has been highlighted using IRMC
(AVR) when local VGA off for easy
identification

CSS indicator

off

no critical event (CSS component)

orange on

prefailure detected (CSS component)

orange
flashing

CSS component failure

Global error
indicator

off

no critical event (non CSS component)

orange on

prefailure detected (non CSS
component)

orange
flashing

non CSS component failure

HDD activity
indicator

green
flashing

data access in progress

Power-on
indicator

off

is off in the following case:

– the system is in power-off mode but

connected to the mains (AC
connected)

green on

is on in the following cases:

– the system has been switched on

and is in power-on delay

– the system is powered on and in

normal operation (S0)

flashes
slowly (1/2
Hz)

iRMC S4 is not ready

Summary of Contents for PRIMERGY TX1330 M2























































































Search results

Summary of Contents for PRIMERGY TX1330 M2

Reviews:

Related manuals for PRIMERGY TX1330 M2

Brands by name

Popular brands

Fujitsu PRIMERGY TX1330 M2, Operating Manual

Search results

Summary of Contents for PRIMERGY TX1330 M2

Reviews:

Related manuals for PRIMERGY TX1330 M2

Brands by name

Popular brands