manualshive.com logo in svg

Fujitsu PRIMERGY RX4770 M4, Operating Manual, Page: 71 / 82

Share
Download
Fujitsu PRIMERGY RX4770 M4 Operating Manual Download Page 71

RX4770 M4

Operating Manual

71

Starting up and operation

6.4

Configuring the server

This section contains information about configuring the server and installing the 
operating system.

I

Make sure that the energy saving functions are disabled in the BIOS 
Setup during server operation.

6.4.1

Configuring the onboard SATA controller

A SATA controller is integrated on the system board. You can configure the 
onboard controller either before or during installation with the ServerView 
Installation Manager. Using the ServerView Installation Manager is 
recommended.

I

In the system BIOS the onboard SATA controller can be configured as 
"AHCI" mode only.

6.4.2

Configuring the SAS/SATA RAID controller

The server can be populated with a SAS/SATA RAID PCIe controller with 
"MegaRAID functionality". You can configure the SAS/SATA RAID controller 
either before or during installation with the ServerView Installation Manager. 
Using the ServerView Installation Manager is recommended.

I

A separate utility is available to the controller for MegaRAID 
configuration. For further information, refer to the "SAS Software User’s 
Guide" (on the Fujitsu manuals server under 

x86 Servers

 - 

Expansion Cards

 

- 

Storage Adapters

 - 

LSI Configuration Software

).

Further information on modular RAID controllers is provided in the 
"Modular RAID Controller Installation Guide" (on the Fujitsu manuals 
server under 

x86 Servers

 - 

Expansion Cards

 - 

Storage Adapters

 - 

LSI SAS / 

SCSI RAID Controllers

).

I

Descriptions of operating systems not covered in the controller manual 
are provided in the corresponding readme under: 

http://www.fujitsu.com/global/services/computing/server/ia/driver/index.html 

.

For Japan:

http://www.fujitsu.com/jp/products/computing/servers/primergy/downloads/

Summary of Contents for PRIMERGY RX4770 M4



















































































Reviews:

No comments