Fujitsu Primergy RX100 S3 User Manual Download

Page: 267 / 287

267

PRIMERGY RX100 S3 User’s Guide

eration

nd
Mainten

ance

9.7 Reinstalling the OS

This section explains the procedure for reinstalling the OS.

9.7.1 Checking before OS Reinstallation

■

Removing the Optional Devices

Remove the following optional devices before reinstallation. Install or connect them after OS

installation.

• External SCSI optional devices (e.g., DAT unit) connected via a SCSI card

• Internal hard disk units that do not contain the OS installation folder

• USB connection option (Excluding the USB connection floppy disk drive and CD-ROM drive)

■

Deletion of Data from the Disc

Reinstallation deletes all disk contents. Be careful. Save the necessary data and system configuration in

a different location.

■

Other Notes

Any remaining notes are the same as those for initial installation. Make sure to check the settings in

advance.

9.7.2 Reinstallation Using ServerStart

When the previous installation was performed in guided mode or preconfiguration mode, the ServerStart

floppy disk used in that installation can be used again. When the reinstallation is performed with the

same configuration as that for the previous installation, you do not have to edit the configuration file on

the ServerStart floppy disk. You do not have to configure setting on wizards. After ServerStart starts up,

click [Start (OS) Installation] to perform installation.

Summary of Contents for Primergy RX100 S3
































































































































































































































































































Search results

Summary of Contents for Primergy RX100 S3

Reviews:

Related manuals for Primergy RX100 S3

Brands by name

Popular brands

Fujitsu Primergy RX100 S3, User Manual

Search results

Summary of Contents for Primergy RX100 S3

Reviews:

Related manuals for Primergy RX100 S3

Brands by name

Popular brands