Fujitsu PRIMERGY CX400 M6 Upgrade And Maintenance Manual Download Page 119

Page: 119 / 209

Preliminary steps

▶

"Locating the defective server" on page 39

▶

If applicable, remove the front bezel, see

"Removing the front bezel" on

page 48

▶

"Locating the defective component" on page 40

Removing the defective 2.5-inch HDD/SSD module

▶

Remove the HDD/SSD module, see

"Removing a 2.5-inch HDD/SSD

module" on page 116

Installing the new 2.5-inch HDD module

▶

Install the HDD/SSD module, see

"Installing 2.5-inch HDD/SSD modules"

on page 112

Concluding steps

▶

If applicable, install the front bezel, see

"Installing the front bezel" on

page 47

▶

If the HDD/SSD is configured using a RAID controller with a RAID level
higher than "0", the rebuild will start automatically, see

"Performing a RAID

array rebuild" on page 89

▶

"Updating Server View RAID Manager" on page 95

7.6

Replacing a 2.5-inch HDD/SSD backplane

Field Replaceable Unit
(FRU)

Hardware: 15 minutes

Tools:

Preliminary and concluding steps: Phillips PH2 / (+) No. 2

Main steps: Phillips PH2 / (+) No. 2

Hard disk drive (HDD) / solid state disk (SSD)

CX400 M6

Upgrade and Maintenance Manual

119

Summary of Contents for PRIMERGY CX400 M6


















































































































































































































Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Brands by name

Popular brands

Fujitsu PRIMERGY CX400 M6, Upgrade And Maintenance Manual

Search results

Summary of Contents for PRIMERGY CX400 M6

Reviews:

Brands by name

Popular brands