Fujitsu PRIMEQUEST 440 System Design Manual Download | Manualshive

Page: 68 / 280

background image

2-10

C122-B001-02EN

CHAPTER 2 General Hardware Configuration

2.3

IO_Unit

This section provides an overview of the IO_Unit. An I/O board, BMM (BMC
module), HDD, PCI cassette, and PCI-X slot are mounted in the IO_Unit, which
provides instructions to devices and inputs and outputs data:

z

The PRIMEQUEST 480 main unit contains one to eight IO_Units, and the
PRIMEQUEST 440 main unit contains one to four IO_Units.

z

SCSI, USB (USB 2.0), and COM ports are provided as the external interfaces.

z

One to four HDDs, which are hot-pluggable, can be mounted.

z

Up to four PCI cards, which are hot-pluggable, can be mounted.

z

Up to two BMMs, which would be IO_Unit control boards, can be mounted as
options.

z

Four PCI-Box interface ports of a serial bus can be mounted.

Figure 2.6 IO_Unit (Full package)

HDD#0

HDD#1

HDD#2

HDD#3

HDD#1

HDD#2

HDD#3

PCI#0

PCI#1

PCI#2

PCI#3

SCSI

PCI_Box

interface

BMM#0 BMM#1

BMM

PCI_Box

interface

Side band

PCI#0

PCI#1

PCI#2

PCI#3

HOME BMM LED
Location LED

USB

RS-232C

Power

Alarm

HDD#0

IOU Power
IOU Alarm

Location

«
...
66
67
68
69
70
...
»

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Related manuals for PRIMEQUEST 440

NEC Express5800 Series

Brand: NEC Pages: 4

NEC Express5800 Series

Brand: NEC Pages: 21

NEC Express5800 Series

Brand: NEC Pages: 10

NEC Express5800 Series

Brand: NEC Pages: 22

NEC Express5800 Series

Brand: NEC Pages: 71

NEC Express5800 Series

Brand: NEC Pages: 166

NEC Express5800 Series

Brand: NEC Pages: 16

Sun Blade T6340

Brand: Sun Oracle Pages: 82

NovaScale T820 F2

Brand: Bull Pages: 34

Flex System x240 Compute Node

Brand: IBM Pages: 28

Brand: Oki Pages: 2

NPort IA5250I/5250I-T Series

Brand: Moxa Technologies Pages: 2

Brand: Docomo Pages: 61

Brand: Cisco Pages: 23

Brand: Cisco Pages: 75

Brand: Cisco Pages: 132

Brand: Cisco Pages: 58

UCS 6400 Series

Brand: Cisco Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands