Fujitsu PRIMEQUEST 440 System Design Manual Download | Manualshive

Page: 52 / 280

background image

1-20

C122-B001-02EN

CHAPTER 1 PRIMEQUEST Overview

Figure 1.13 Duplication of the main components

Hot maintenance function

The hot maintenance function disconnects a unit from the system for maintenance
work on the unit, without stopping system operation.

Hot maintenance is possible because the main components and important units in a
PRIMEQUEST-series machine are in redundant configurations, as described below:

z

Since the power supply units (PSUs) and fans are in redundant configurations as
standard, hot maintenance of PSUs and fans is possible.

z

Since the MMB, which provides the server management function, is in a redundant
configuration, hot maintenance of the MMB is possible.

z

Hot maintenance of an SB, IO_Unit, HDD, system interconnect, PCI card, GSWB,
and other devices is possible under specific conditions.

z

Hot maintenance of a non-duplicated KVM unit and OPL is also possible.

Management LAN

duplication

Business LAN

duplication

Crossbar

MMB

#0

MMB

#1

IOU

#1

IOU

#2

IOU

#3

IOU

#4

IOU

#5

IOU

#6

IOU

#7

SB
#1

SB#0

SB
#2

SB
#3

SB
#4

SB
#5

SB
#6

SB
#7

GSWB#0

GSWB#1

BP

BP

IOU#0

«
...
50
51
52
53
54
...
»

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Related manuals for PRIMEQUEST 440

Express5800/180Ra-7

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rh-2

Brand: NEC Pages: 2

Express5800/120Rg-1

Brand: NEC Pages: 2

Express5800/120Rf-1

Brand: NEC Pages: 21

Express5800/120Ra-1

Brand: NEC Pages: 6

Express5800/120Mc2 series

Brand: NEC Pages: 2

EXPRESS5800/120Le

Brand: NEC Pages: 56

Express5800 320La

Brand: NEC Pages: 8

Express5800 120Li

Brand: NEC Pages: 2

Express5800 120Ed

Brand: NEC Pages: 29

Active Upgrade Express5800/320Fc

Brand: NEC Pages: 4

Brand: NEC Pages: 10

Express5800/120Rj-2

Brand: NEC Pages: 18

Express5800/120Rh-1

Brand: NEC Pages: 20

Bull NovaScale R620 Series

Brand: NEC Pages: 346

Express5800 320La

Brand: NEC Pages: 206

Express5800/R110j-1

Brand: NEC Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands