Fujitsu PRIMEQUEST 440 System Design Manual Download | Manualshive

Page: 242 / 280

background image

10-8

C122-B001-02EN

CHAPTER 10 Backup and Restoration

z

ACM Agent

Controls the AdvancedCopy function of the ETERNUS. ACM Agent is installed
in the business server that is a backup target.

z

ACM Tape Server

Controls the tape library and the backup to and restoration from tape media. The
tape library is connected to a partition in which ACM Tape Server is installed.
ACM Tape Server and ACM Manager can be installed in the same partition.

Configuration example when VERITAS NetBackup is used (Linux)

• Normal backup of data

Use the LAN or SAN, back up client data to a tape unit connected to a backup server.
As a backup destination, the user can specify a disk area connected to the backup
server.

Figure 10.5 Data backup using VERITAS NetBackup

«
...
240
241
242
243
244
...
»

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Related manuals for PRIMEQUEST 440

Brand: Panasonic Pages: 28

Brand: Far south networks Pages: 4

Brand: Xerox Pages: 12

Brand: Sercomm Pages: 75

Brand: Rackable Systems Pages: 4

Brand: Discover Video Pages: 148

AND-APL1E Series

Brand: Acrosser Technology Pages: 42

Brand: IBM Pages: 90

Brand: Xerox Pages: 2

Brand: Sonnet Pages: 16

Brand: Biamp Pages: 11

Brand: Black Box Pages: 4

Brand: Black Box Pages: 12

Brand: Blonder tongue Pages: 20

AirProjector KJ-200

Brand: TriLink Pages: 56

Brand: Supero Pages: 98

AS-4021M-82R Plus

Brand: Supero Pages: 106

Brand: Supero Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands