manualshive.com logo in svg

Fujitsu PRIMEQUEST 440, System Design Manual

Share
Download
Fujitsu PRIMEQUEST 440 System Design Manual Download Page 235

C122-B001-02EN

10-1

 

CHAPTER 10  Backup and Restoration

1

This chapter describes the importance of backing up data, backup methods, and 
restoration methods.

10.1

  Importance of Backing Up Data

PRIMEQUEST uses components and hardware with high reliability and duplicates 
many units to maintain high reliability.  To be prepared for failure occurrences, 
however, be sure to back up data periodically.

If a system is damaged due to some problem, or if data on a server is deleted by an 
operator error and the like, the data on the PRIMEQUEST system needs to have been 
backed up to recover the data in the server to its previous status.

As long as data is backed up, if data in a hard disk drive is damaged due to a hardware 
failure, an operator error, and the like, the user can restore the backup data and 
recover normal system operation.  If the data is not backed up, it will be lost.

Be sure to back up data periodically to operate a system with confidence.

10.2

  General Methods of Backup and Restoration

The following four methods of backing up and restoring a system are available:

- Using the standard utilities included in an OS

 

Linux:

dump/restore

 

Windows:

NTBackup

- Using cloning software

 

Common to Linux and Windows: SystemcastWizard Lite

- Using backup software

 

Linux: Softek ACM, VERITAS NetBackup, NetVault,

 

NetWorker, Softek TSM 

- Using appliance (ETERNUS SP5000) with storage backup functions 

 

Common to Linux and Windows:

ETERNUS SP5000

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands