Fujitsu PRIMEQUEST 400 Series Installation Manual Download Page 155

Page: 155 / 446

C122-E001-10EN

3-33

3.3 Windows Installation

3.3.3

Windows installation using the installation support tool

3.3.3.1

Overview

Installation Support Tool for Windows is an automatic Windows installation tool

supplied with the PRIMEQUEST server.

Installation Support Tool for Windows requires that the parameters used for

installation be entered on a (32-bit) computer running Windows and saved on a floppy

disk in advance. This floppy disk is called the "installation floppy disk."

Using the installation floppy disk, Installation Support Tool for Windows enables

automatic installation of Windows on the PRIMEQUEST-series machine from the

Windows installation DVD. After Windows is installed, the PRIMEQUEST Software

Installer runs to install drivers and monitoring tools required for stable operation.

Installation using Installation Support Tool for Windows has the following

advantages:

•

Using an installation floppy disk that has been verified in advance can prevent

procedural mistakes during installation.

•

Operations for installing Windows in multiple partitions having the same

configuration are easy to perform.

•

Compared with installation using SystemcastWizard Lite, equipment handling is

easy because a single floppy disk contains the necessary data. No device other

than a USB floppy disk drive is required for installation.

Installation Support Tool for Windows is included in the following path on the

"PRIMEQUEST Drivers CD for Microsoft

Windows Server

2003" (C122-E024)

(referred to as the Drivers CD, in this document) supplied with the PRIMEQUEST

product:

E:\Tools\General\IST (where the CD-ROM drive is Drive E)

For details, see the Readme file and the PRIMEQUEST Installation Support Tool for

Windows User's Guide (C122-048EN).

Summary of Contents for PRIMEQUEST 400 Series































































































































































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 400 Series

Reviews:

Fujitsu PRIMEQUEST 400 Series, Installation Manual, Page: 155 / 446

Search results

Summary of Contents for PRIMEQUEST 400 Series

Reviews: