Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 83

Page: 83 / 344

3.4.6

Configuring Console Redirection

To remotely install an operating system, you need to first configure Console Redirection.

Set Console Redirection to the same subnet as the management LAN.

1. Click [Partition] - [Console Redirection Setup].

>> The [Console Redirection Setup] window appears. For details on this window, see 1.3.6 [Console

Redirection Setup] window in the

PRIMEQUEST 1000 Series Tool Reference

(C122-E110EN).

FIGURE 3.30 [Console Redirection Setup] window (example)

2. Set the IP address.

3. Enable each of video redirection, remote storage, and text console redirection.

4. Click the [Apply] button.

Note

After the installation, disable the functions that will not be used.

3.4.7

Powering off and on a partition

To apply the configuration changes to a partition, power off and on the partition.

For details on how to power off and on a partition, see

CHAPTER 8 Powering On and Off a Partition

Remarks

After POST ends, processing continues until the [EFI Shell] window appears when the console is connected to the

partition, and then it stops.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 3 Work before Operating System Installation

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Fujitsu PRIMEQUEST 1000 Series, Installation Manual, Page: 83 / 344

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews: