Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 37

Page: 37 / 344

2.4

Preparing the Power Supply Equipment

This section describes the electrical specifications, facility power requirements, and grounding for the

PRIMEQUEST 1000 series.

To prevent accidents, confirm that the power supply equipment can supply enough power to the system. Electrical

engineering and installation work shall conform to local ordinances and local and national government regulations.

For details on the power supply equipment, see the

SPARC Enterprise/PRIMEQUEST Common Installation

Planning Manual

(C120-H007EN).

2.4.1

Electrical specifications

For details on the electrical specifications of the PRIMEQUEST 1000 series, see 1.3 Installation Specifications in

the

PRIMEQUEST 1000 Series Hardware Installation Manual

(C122-H004EN).

For details on the power cables, see 2.2.1 Basic interfaces and peripheral devices (PRIMEQUEST 1800E2) or

2.2.2 Basic interfaces and peripheral devices (PRIMEQUEST 1800E) in the

PRIMEQUEST 1000 Series Hardware

Installation Manual

(C122-H004EN).

For details on the connectors and their shapes, see 2.4.1 PRIMEQUEST 1000 series main unit in the

PRIMEQUEST

1000 Series Hardware Installation Manual

(C122-H004EN).

2.4.2

Facility power requirements and characteristics

To obtain the required degree of redundancy, the facility must have two independent supplies of power. Connect

the circuit breakers to the power receiver provided by the electric power company or to a UPS (uninterruptible

power supply).

If the main unit operates in an environment that experiences frequent power failures or has a power source that

often becomes unstable, the component failure rate tends to rise.

The PRIMEQUEST 1000 series supports the basic connection configurations shown in the following diagrams:

- Power line diagram for redundant power connections

- Power line diagram for dual power connections

For details on the power line configurations for redundant power connections and dual power connections, see 2.3

Power Cable Connections in the

PRIMEQUEST 1000 Series Hardware Installation Manual

(C122-H004EN).

2.4.3

Grounding

The PRIMEQUEST 1000 series is shipped with grounded (three-wire) power cables. You need to connect the power

cables to outlets with ground terminals. To determine the type of power supply in your building, contact the building

manager or a qualified electrical engineer.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 2 Preparing for Main Unit Installation

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands