Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 185

Page: 185 / 344

FIGURE 6.2 [Add a Port] dialog box (SNMP)

5. Enter the port number used by SNMP. Then, click the [OK] button.

6. Click the [OK] button in the [Windows Firewall] window.

6.3.6

Setting the Watchdog Timer for monitoring after a STOP error (fatal
system error)

If a STOP error (fatal system error) occurs in the system, the following situation results.

- After you select [Partition] - [Power Control] from the MMB Web-UI, the window displays "Stop Error"

under [System Progress] for the relevant partition.

- The system acquires a memory dump.

You can set monitoring with the Watchdog Timer to perform recovery after the system freezes or otherwise becomes

unresponsive in the above event.

Immediately after the specified time elapses, the MMB performs a Hard Reset to reboot the operating system.

Operations

1. Open the following file:

PSA installation folder

\etc\opt\FJSVpsa\usr\pnwatchdog.conf

Example: C:\fujitsu\FJSVpsa\etc\opt\FJSVpsa\usr\pnwatchdog.conf

2. Specify the value of the following key. The default is 0.

Section: [WATCHDOG]

Key: [TIMER]

Setting value (unit: seconds): 0 (Watchdog Timer disabled), 1 to 6000 (Watchdog Timer monitoring time)

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

157

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands