Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 162

Page: 162 / 344

6.2.2

Confirming management LAN settings

Make network settings for the management LAN. If necessary, also configure any duplication with bonding or

PRIMECLUSTER GLS, for example.

After completing the above network settings for the management LAN, perform the operations described in

6.2.4

Checking the firewall function (opening ports)

and

6.2.7 Setting the management LAN IP address

Note

In the PRIMEQUEST environment, it is necessary to specify OFF for the STP function of the switch that connects

to the management LAN used for communication with the MMB.

6.2.3

Confirming SELinux function settings

This section describes the SELinux settings and how to confirm them.

Other OS settings

- For RHEL5

If the partition OS with PSA installed is running RHEL5, disable the SELinux functions. When installing

PSA, the SELinux functions are automatically disabled. Confirm that the SELinux functions are disabled. If

the SELinux functions are enabled, disable them.

- For RHEL6.0/RHEL6.1

If the partition OS with PSA installed is running RHEL6.0/RHEL6.1, disable the SELinux functions. When

installing PSA, the SELinux functions are not automatically disabled. Check the SELinux function setting.

If the SELinux functions are enabled, disable them.

- For RHEL6.2 or later

If the partition OS with PSA installed is running RHEL6.2 or later, it operates irrespective of whether the

SELinux functions are enabled or disabled.

The procedure for confirming the SELinux function setting and disabling the SELinux functions is as follows.

Confirm that the following command displays "disabled" when operating the system with the SELinux functions

disabled. If the command displays anything other than "disabled," disable the functions by editing the config file

(/etc/selinux/config).

Confirming settings

#cd /etc/selinux/

#more config

.....

SELinux=disabled

←

Confirm this.

Changing settings

# vi /etc/selinux/config

.....

SELinux=disabled

←

Edit this.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 6 Work after Operating System Installation (PRIMEQUEST 1800E)

134

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands