Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 153

Page: 153 / 344

TABLE 5.3 Message for advance notification of replacement and replacement notification message
(UPS)

Start time for sending messages for advance

notification of replacement

Time for sending replacement

notification message

After about 1 year and 9 months from the start

of use or replacement of the battery unit

After about 2 years

Operations

1. Determine which partitions to set for service life monitoring. Then, start the GUI of RAS Support Service.

- Windows: Log in to the operating system. Start the GUI.

- Linux: Open a Web browser. Access the specified URL. Log in.

For details on operations, see the

RAS Support Service User's Guide (for Linux or Windows)

2. The Service Life Component Names list on the RAS Support Service screen displays [UPS (battery)].

Since you can enter a value in the Mounting Dates list, enter the battery unit mounting date in the list.

Notes

Note the following points about service life monitoring of the battery unit for a UPS in the PRIMEQUEST 1800E2.

- If there are multiple partition configurations, set battery unit service life monitoring for a UPS for only one

partition (arbitrary).

Otherwise, advance notifications of replacement will be issued from multiple partitions.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 5 Work after Operating System Installation (PRIMEQUEST 1800E2)

125

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands