Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 140

Page: 140 / 344

FIGURE 4.14 Example of display of the [Change Boot Order] menu

The following describes the meaning of the menu:

- UEFI: DVD/CD n (n=0, 1, 2...)

Specify this when starting the UEFI-awareOS from the external DVD/CD drive media.

The n in "UEFI: DVD/CD n" is a sequential number (starting from 0) assigned in the order that

DVD/CD devices are recognized. The assigned number remains stored based on the connection

location information as long as the device is not disconnected from the system.

- UEFI: Embedded DVD/CD:

Specify this item when using the built-in DVD drive for installation in UEFI mode.

- UEFI Shell:

Specify this menu when starting UEFI Shell. The PRIMEQUEST 1000 series does not use UEFI

Shell.

- Legacy Boot:

Specify this item for BIOS mode. Also specify [Legacy Boot] when using the built-in DVD drive

for installation in BIOS mode.

3. Specify [Commit Changes and Exit] - [Reset System] to reboot the partition.

3. After a moment, the language selection window appears. Select [English] for installation in English.

4. Click the [Next] button on the initially displayed window without setting anything.

5. Select [Deployment] in the [Welcome to ServerView Installation Manager] window.

6. Select an installation mode and the operating system to be installed. Then, set up the operating system.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

112

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands