Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 113

Page: 113 / 344

8. Replace the media with the operating system installation media according to the SVIM instructions.

9. Perform the following operation by using the MMB Web-UI.

Remarks

These steps are not required in Windows Server 2012.

1. Click [Partition] - [Partition#x] - [Mode].

2. Check the [Setting OS Installation Mode] check box, and then click the [Apply] button.

3. When the confirmation message appears, click the [OK] button.

After a while, the [Setting Completed] window appears. This completes the setting procedure.

FIGURE 4.8 [Mode] window (example)

Remark

Perform the above procedure at the following times.

1. When the system goes from the [ServerView Installation Manager] window to the [Install Windows] window,

after starting installation with SVIM and rebooting.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands