Fujitsu PRIMEQUEST 1000 Series Installation Manual Download Page 112

Page: 112 / 344

FIGURE 4.7 Example of display of the [Change Boot Order] menu

The following describes the meaning of the menu:

- UEFI: DVD/CD n (n=0, 1, 2...)

Specify this when starting the UEFI-aware OS from the external DVD/CD drive media.

The n in "UEFI: DVD/CD n" is a sequential number (starting from 0) assigned in the order that

DVD/CD devices are recognized. The assigned number remains stored based on the connection

location information as long as the device is not disconnected from the system.

- UEFI: Embedded DVD/CD:

Specify this item when using the built-in DVD drive for installation in UEFI mode.

- UEFI Shell:

Specify this menu when starting UEFI Shell. The PRIMEQUEST 1000 series does not use UEFI

Shell.

- Legacy Boot:

Specify this item for BIOS mode. Also specify [Legacy Boot] when using the built-in DVD drive

for installation in BIOS mode.

3. Specify [Commit Changes and Exit] - [Reset System] to reboot the partition.

3. After a moment, the language selection window appears. Select [English] for installation in English.

4. Click the [Next] button on the initially displayed window without setting anything.

5. Select [Deployment] in the [Welcome to ServerView Installation Manager] window.

6. Select an installation mode and the operating system to be installed. Then, set up the operating system.

Remark

The IP address of the LAN cannot be set through the operating system setup. Set the IP address after the

installation of the operating system.

7. Click [Install].

Installation begins.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

C122-E107-09EN

Summary of Contents for PRIMEQUEST 1000 Series

























































































































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands

Fujitsu PRIMEQUEST 1000 Series, Installation Manual

Search results

Summary of Contents for PRIMEQUEST 1000 Series

Reviews:

Related manuals for PRIMEQUEST 1000 Series

Brands by name

Popular brands