Fujitsu MB95630H Series Hardware Manual Download | Manualshive

Page: 440 / 644

background image

MB95630H Series

420

FUJITSU SEMICONDUCTOR LIMITED

MN702-00009-1v0-E

CHAPTER 21 MULTI-PULSE GENERATOR
21.5 Operations

21.5.6

Operation of Noise Cancellation Function

This section describes the noise cancellation function for the SNIx and DTTI
pins.

■

Operation of Noise Cancellation Function

●

DTTI Pin Noise Cancellation Function

When the NRSL bit in the 16-bit MPG output control register (upper) (OPCUR) is set to "1",

the noise cancellation function for DTTI pin input can be used. When the noise cancellation

function is selected, the time for fixing an output pin at the inactive level is delayed for about 4,

8, 16 or 32 machine clocks by the noise cancellation circuit.

Note:

Since the DTTI input control circuit uses a peripheral clock, input is invalidated even if the
DTTI input is enabled in a mode such as stop mode in which the oscillator stops.

●

SNI2 to SNI0 Pins Noise Cancellation Function

When SNC[2:0] bits in the 16-bit MPG input control register (lower) (IPCLR) are set to "1",

the noise cancellation function for SNI2 to SNI0 pins input can be used. When the noise

cancellation function is selected, the input is delayed for about four machine clocks by the

noise cancellation circuit. Since the noise cancellation circuit uses a peripheral clock, input is

invalidated in a mode such as STOP mode in which the oscillator stops even if the SNIx input

is enabled.

●

Programmable Noise Cancellation Circuit

Noise to be cancelled is programmable to have pulse width less than 4, 8, 16 and 32 machine

cycles, i.e. for 16 MHz machine clock, the circuit can filter 0.25 µs to 2 µs width pulses. The

control for the programming of the noise cancellation circuit of the SNIx and DTTI pins are

separated. Section "21.6.9 16-bit MPG Noise Cancellation Control Register (NCCR)" shows

the noise cancellation control register.

«
...
438
439
440
441
442
...
»

Summary of Contents for MB95630H Series





































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MB95630H Series

Brand: Keithley Pages: 59

Brand: Zenith Data Systems Pages: 64

Brand: STONEFLY Pages: 48

JetWeb JX2-PR0FI1

Brand: Jetter Pages: 67

Brand: Rolls Pages: 2

APS6-400 Series

Brand: Eaton Pages: 114

Brand: Dolphin Pages: 9

Brand: Kanguru Pages: 13

Brand: ADS Technologies Pages: 1

PFC Chokes PFC3515V Series

Brand: Delta Electronics Pages: 1

BiPAC 5200S RC Series

Brand: Billion Pages: 79

Brand: RR-Concepts Pages: 12

Brand: Omron Pages: 14

NVR2104/2108HS-W-4KS2 1U

Brand: Dahua Technology Pages: 363

EK-Quantum Vector FTW3 RTX 2080 Ti

Brand: ekwb Pages: 3

Brand: NEC Pages: 114

Brand: Behringer Pages: 12

Brand: LSIS Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands