manualshive.com logo in svg

Fujitsu MB91150 Series, Hardware Manual, Page: 434 / 512

Share
Download
Fujitsu MB91150 Series Hardware Manual Download Page 434

418

CHAPTER 21  FLASH MEMORY

21.2 Flash Memory Registers

Flash memory has a status register (FLCR) and a wait register (FWTC).

■

Status register (FLCR) (CPU mode)

Register indicating the operating status of the flash memory. The FLCR controls CPU interrupts
and writing to the flash memory.

The FLCR can be accessed only in CPU mode. Do not access the FLCR with a Read Modifier
Write instruction.

The structure of the FLCR is as follows:

[Bit 7]: INTE (INTerrupt Enable)

Bit 7 is used to control the automatic algorithm (e.g., write and erase) termination interrupt
output of the flash memory.

•

At reset, this bit is initialized to 0.

•

This bit can both be read and written.

[Bit 6]: RDYINT (Ready interrupt)

Bit 6 is set to 1 when the automatic algorithm (e.g., write and erase) of the flash memory
terminates.

If this bit is set to 1 when bit 7 (INTE) is 1, an automatic algorithm termination interrupt
request is issued

•

At reset, this bit is initialized to 0.

•

This bit can both be read and written. However, it can only be set to 0. The value of this bit
remains unchanged even there is an attempt to set it to 1.

bit 7

INTE

R/W

(0)

bit 5

WE

R/W

(0)

bit 4

RDY

R

(X)

bit 3

(X)

bit 2

(X)

bit 1

(X)

bit 0

LPM

R/W

(0)

0007C0 h

bit 6

RDYINT

R/W

(0)

0

Disables automatic algorithm termination interrupt output.

1

Enables automatic algorithm termination interrupt output.

0

Automatic algorithm termination was not detected.

1

Automatic algorithm termination was detected.

Summary of Contents for MB91150 Series

































































































































































































































































































































































































































































































































Reviews:

No comments