manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 614 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 614

595

CHAPTER 23  512K / 1024K BIT FLASH MEMORY

23.5.1

Data Polling Flag (DQ7)

The data polling flag (DQ7) indicates whether the automatic algorithm is being executed 
or has been terminated, using the data polling function.  Table 23.5-3 shows the data 
polling flag status transition.

■

When the Write Operation is Executed.

When the read/access is executed during automatic write algorithm execution, the flash memory outputs the

reverse data of bit7 in the last-written data, irrespective of the specified address.  When the read/access is

executed at the end of the automatic write algorithm, the flash memory outputs the data of bit7 in the

specified read address.  When the read/access is executed at the end of the automatic write algorithm, the

flash memory outputs the data of bit7 in the specified read address.

■

When the Chip/Sector Deletion Operation is Executed.

When the read/access is executed during the chip/sector deletion algorithm execution, the flash memory

outputs "0" from the sector being deleted by the sector deletion, or irrespective of the specified address

during the chip deletion.  Similarly, the flash memory outputs "1" at the end of chip/sector deletion

algorithm.

■

When the Sector Deletion Temporary Stop is Executed.

When the access/read is executed while executing the sector deletion temporary stop, the flash memory

outputs "1" if the specified address is the sector being deleted.  However, the flash memory outputs the data

of bit7 (DATA:7) of the specified read address, if the specified address is not the sector being deleted.  By

referencing this together with the toggle bit flag (DQ6), it can be determined whether the current sector is

in the temporary stop state or which sector is being deleted.

Note:

When the automatic algorithm is started, the read/access to the specified address is ignored.  As for
the data reading, the end of data polling flag (DQ7) is posted, and then other data bit can be output.
Therefore, the data read operation after the end of the automatic algorithm should be executed next
to the read/access after verifying the end of data polling flag.

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments