manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 580 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 580

561

CHAPTER 20  8/10-BIT A/D CONVERTER

20.6.2

  A/D Conversion Data Protection Function

When A/D conversion is performed in the interrupt enabled state, the conversion data 
protection function operates.

■

A/D Conversion Data Protection Function

The A/D converter has just one data register that holds conversion data.  When a single A/D conversion is

completed, the data in the data register is rewritten.

If the conversion data were not transferred to memory before the next conversion data was stored, part of

the conversion data would be lost.  The data protection function operates in the interrupt enabled state

(INTE = 1), as described below, to prevent loss of data.

●

Data protection function when 

EI

2

OS

 is not used

When conversion data is stored in the A/D data register (ADCR0/ADCR1), the INT bit of the A/D control

status register1 (ADCS1) is set to "1".

While the INT bit is "1", A/D conversion is halted.

Halt status is released when the INT bit is cleared after data in the A/D data register (ADCR0/ADCR1) has

been transferred to memory by the interrupt routine.

●

Data protection function when 

EI

2

OS

 is used

In continuous conversion using EI

2

OS, the PAUS bit of the A/D control status register1 (ADCS1) is kept at

"1" when a conversion ends.  This status continues until EI

2

OS finishes transferring the conversion data

from the data register to memory.  In the meantime, the A/D conversion is halted, and the next conversion

data is not stored.  When the data transfer to memory is completed, the PAUS bit is cleared to "0" and

conversion resumes.

Figure 20.6-5 shows the operation flow of the data protection function when EI

2

OS is used.

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments