manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 420 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 420

401

CHAPTER 15  MULTI-PULSE GENERATOR

15.6.2

Operation of Data Write Control Unit

The Data Write Control Unit is used to generate the write timing output (WTO) for 
transferring data from the Output Data Buffer Register (OPDBR) to Output Data Register 
(OPDR). 

■

Operation of Data Write Control Unit

The Write Timing Output (WTO) can be generated by the following condition:

•

After OPDBR0 is written by software.

•

Triggered by the 16-bit reload timer 0 underflow. 

•

Triggered by the 16-bit reload timer 0 underflow. The 16-bit timer is started by the position detection

comparison circuit.

•

Triggered by the position detection input (SNI2 to SNI0) (16-bit Reload timer 0 acts as a delay).

•

Triggered either by the 16-bit reload timer 0 underflow, or by the position detection input.

At the mean time the cause of generation of WTO will be defined by setting different value of OPS2 to

OPS0 bit of the Output Control Register (OPCR: OPS2 to OPS0).

■

Signal Flow Diagram for OPDBR0 by Setting OPS2 to OPS0 = 000

B

Figure 15.6-5  Signal Flow Diagram for OPDBR0 (OPS2 to OPS0 = 000

B

)

The write timing output signal is generated from the Data Write Control Unit whenever a value is written to

the OPDBR0 register, and the data in OPDBR0 is transferred to OPDR register one cycle later. 

POSITION

16-BIT RELOAD TIMER 0

TIN

TOUT

DETECTION

TIN0O

WTIN0

WTIN1

WTO

TIN0

SNI2 to

TIN0

WRITE
TIMING

DATA WRITE CONTROL UNIT

OPDBR0W

OPDBR0 WRITE SIGNAL

OUTPUT

Pin

Pin

SNI0

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments