manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 365 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 365

346

CHAPTER 14  MULTI-FUNCTIONAL TIMER

■

Making Non-overlap Signals by using PPG in Inverted Polarity 
(DTCR0/DTCR1/DTCR2:TMD2 to TMD0=111

B

)

When selecting non-overlap signal for an active level "1" (inverted polarity) in DTCR0/DTCR1/

DTCR2:DMOD, a delay corresponding to the non-overlap time set in the TMRR0/TMRR1/TMRR2

register (16-bit timer register) is applied. The delay is applied at a rising edge of PPG timer 0 pulse signal

or its inverted signal. If PPG timer 0 pulse width is smaller than the set non-overlap time, the 16-bit timer

will start down-counting from TMMR0/TMMR1/TMMR2 value at the next edge of PPG0 pulse.

Figure 14.6-28  Non-overlap Signal Generation by PPG0 in Inverted Polarity

Setting up registers:

• TCDT

: 

0000

H

 

• TCCS

: 

XXXXXXXXXX0X0XXX

B

• CPCLR

: 

XXXX

H

 (Cycle setting)

•  OCCP0 to OCCP5

:XXXX

H

 (Compare value)

•  OCS0 to OCS5

: -XX1XXXXXXXXXX11

B

•  DTCR0 to DTCR2

: 1XXXX111

B

•  TMRR0 to TMRR2

: XXXX

H

 (Non-overlap timing setting)

• SIGCR

: 

XXXXXXXX

B

 (DTTI0 input and 16-bit timer count clock setting)

Note:

“

X

”

 must be set according to the operation.

Count
value

PPG0

RTO0 (U)

RTO1 (X)

1 machine cycle

1.5 machine cycle

TMRR0 set value

Pin name

Output signal

RTO0 (U)

Inverted signal with delay is applied at PPG0 rising edge

RTO2 (V)

Inverted signal with delay is applied at PPG0 rising edge

RTO4 (W)

Inverted signal with delay is applied at PPG0 rising edge

RTO1 (X)

Signal with delay is applied at PPG0 falling edge

RTO3 (Y)

Signal with delay is applied at PPG0 falling edge

RTO5 (Z)

Signal with delay is applied at PPG0 falling edge

16-bit timer 0

• PCSR

: 

XXXX

H

• PDUT

: 

XXXX

H

• PCNT

: 

XXXX

H

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments