manualshive.com logo in svg

Fujitsu MB90460 Series, Hardware Manual, Page: 145 / 739

Share
Download
Fujitsu MB90460 Series Hardware Manual Download Page 145

126

CHAPTER 7  INTERRUPT

7.4

Hardware Interrupt

The hardware interrupt function temporarily interrupts the program being executed by 
the CPU and transfers control to a user-defined interrupt processing program in 
response to an interrupt signal from a peripheral function.

The extended intelligent I/O service (EI

2

OS) and external interrupt are executed as a 

type of hardware interrupt.

■

Hardware Interrupt 

●

Hardware interrupt function

The hardware interrupt function compares the interrupt level of the interrupt request signal output by a

peripheral function with the interrupt level mask register (ILM) in the CPU processor status (PS).  The

function then references the contents of the I flag in the processor status (PS) through the hardware and

decides if the interrupt can be accepted.

When the hardware interrupt is accepted, the CPU internal registers are automatically saved on the system

stack.  The currently requested interrupt level is stored in the interrupt level mask register (ILM), and the

function branches to the corresponding interrupt vector.

●

Multiple interrupts

Multiple hardware interrupts can be activated.

●

Extended intelligent I/O service (EI

2

OS)

EI

2

OS is an automatic transfer function between memory and I/O.  When the specified transfer count has

been completed, a hardware interrupt is activated.  Multiple EI

2

OS activation does not occur.  During

EI

2

OS processing, all other interrupt requests and EI

2

OS requests are held.

●

External interrupt

An external interrupt (including wake-up interrupt) is accepted from a peripheral function (interrupt request

detection circuit) as a hardware interrupt.

●

Interrupt vector

Interrupt vector tables referenced during interrupt processing are allocated to memory at FFFC00

H

 to

FFFFFF

H

.  These tables are shared by software interrupts.

See "7.2  Interrupt Causes and Interrupt Vectors", for more information about the allocation of interrupt

numbers and interrupt vectors.

Summary of Contents for MB90460 Series




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments