Fujitsu General AOHG45KRTA Service Manual Download Page 124

Page: 124 / 154

7-5. Compressor temperature protection

When the compressor temperature sensor detects higher than the trigger condition below, the com-
pressor is stopped. When the compressor temperature sensor detects the release condition, the pro-
tection is released.

Trigger condition

108°C

Release condition

80°C

(3 minutes after compressor stop)

7-6. High pressure protection

Trigger condition

Pressure switch: Off (Open: Higher than 4.2 MPa)

Compressor stop

Release condition

Pressure switch: On (Close: Lower than 3.2 MPa)

(3 minutes after compressor stop)

Compressor restart

7-7. Low outdoor temperature protection

When the outdoor temperature sensor detects lower than the trigger condition below, the compres-
sor is stopped.

Operation mode

Cooling/Dry

Trigger condition

-20°C

Release condition

-15°C

7-5. Compressor temperature protection

- (04-30) -

7. Various protections

CONTROL AND

FUNCTIONS

CONTROL AND

FUNCTIONS

Summary of Contents for General AOHG45KRTA



























































































































































Search results

Summary of Contents for General AOHG45KRTA

Reviews:

Fujitsu General AOHG45KRTA, Service Manual, Page: 124 / 154

Search results

Summary of Contents for General AOHG45KRTA

Reviews: