background image

1

F u j i t s u   A m e r i c a ,   I n c .

This user’s guide contains information on using the dual battery 

charger. We strongly recommend that you read this guide before 

using the battery charger.

BATTERY CHARGER COMPONENTS

The battery charging station (referred to in this document as the 

“charger”) is a versatile device that allows you to charge a 

variety of different battery packs simultaneously.
The charger consists of the following components:
• Charger base with built-in AC adapter 
• U. S. power cord
Additionally, removable adapter modules are required to 

accommodate your specific battery types. 

The adapter 

modules must be ordered separately from the charger.

 

BATTERY CHARGER FEATURES

Refer to Figure 1 for the location of the following features.

Charger Base. 

The charger base holds the adapter modules 

and contains the power supply.

Power Indicator. 

The power indicator shows whether power 

is applied to the charger. When the power cord is disconnected 

and/or the power switch is shut off, this indicator is off. When 

power is applied, this indicator is solid green.

Indicator LEDs. 

Each of the battery bays has two LEDs asso-

ciated with it: The upper LEDs indicate charge level (as detailed 

in the table below); the lower LEDs indicate a battery error.

Battery Charging Station 
User’s Guide

Battery Charging Station B5FY-9511-02EN-00.fm  Page 1  Friday, December 17, 2010  9:23 AM

Summary of Contents for FPCBC27













Reviews: