Fujitsu fi-7300NX Operator'S Manual Download

Page: 91 / 321

Combinations of Standard Paper Sizes in a Mixed Batch

Refer to the table below for a guideline of the range available for mixed batch scanning.

LTR: Letter size

A3-CS:Carrier Sheet

(P): Portrait

(L): Landscape

ATTENTION

B8 (portrait) and A8 (portrait) documents cannot be mixed with other sizes in the same batch.

Documents That Cannot Be Scanned in a Mixed Batch

The following types of documents cannot be mixed in the same batch:

●

Carbonless paper

●

Bond paper

●

Perforated documents

●

Thermal paper

●

Carbon-backed paper

●

OHP film

How to Load Documents

Summary of Contents for fi-7300NX


































































































































































































































































































































Search results

Summary of Contents for fi-7300NX

Reviews:

Related manuals for fi-7300NX

Brands by name

Popular brands

Fujitsu fi-7300NX, Operator'S Manual

Search results

Summary of Contents for fi-7300NX

Reviews:

Related manuals for fi-7300NX

Brands by name

Popular brands