Fujitsu fi-7300NX Operator'S Manual Download | Manualshive

Page: 293 / 321

background image

Specifying the Area to Detect Overlapped Documents [Document check area
specification for Multifeed Detection]

Specify an area to detect overlapped documents.
Specify this item when [Check Overlapping(Ultrasonic)] or [Check Overlapping and Length] is selected for
[Multifeed].

1

Start up the Software Operation Panel.
For details, refer to

Starting Up the Software Operation Panel (page 248)

2

From the list on the left, select [Device Setting 2] → [Document check area specification for Multifeed
Detection].
Select the [Selected range] check box in the window.

3

Specify the detection range.

Scanner Settings (Software Operation Panel)

293

«
...
291
292
293
294
295
...
»

Summary of Contents for fi-7300NX


































































































































































































































































































































Reviews:

No comments

Related manuals for fi-7300NX

Brand: C-Pen Pages: 20

Brand: C-Pen Pages: 8

Brand: Quins Pages: 14

Brand: Eclipse Pages: 6

Rosemount 5708 3D Solids Scanner DeltaV Series

Brand: Emerson Pages: 32

Brand: Emerson Pages: 204

Brand: Kaixin Pages: 33

Brand: PROEL Pages: 57

Brand: Katsuragawa Electric Pages: 28

Scantrak RP-6120

Brand: RCA Pages: 2

Brand: 3nStar Pages: 2

Brand: Pakon Pages: 29

Brand: Radio Shack Pages: 44

Brand: MAGINON Pages: 28

Brand: Uniden Pages: 152

wall mount Multi-Channel DPS3300

Brand: Omega Engineering Pages: 31

Brand: Microtek Pages: 3

Brand: Microtek Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands