Fujitsu fi-7300NX Operator'S Manual Download | Manualshive

Page: 281 / 321

background image

Feeding [Pick Speed]

You can specify the timing of when document feeding is started.
When overlapped documents or paper jams occur frequently, delaying the timing of document feeding may improve
the performance.
This setting is effective when you scan thin paper.

1

Start up the Software Operation Panel.
For details, refer to

Starting Up the Software Operation Panel (page 248)

2

From the list on the left, select [Device Setting 2] → [Pick Speed].

3

Select the feeding speed.

Normal

This is the optimum feeding speed.
This is the factory default setting.

Slower

The timing of document feeding is delayed more than [Normal].

ATTENTION

The total time for scanning is longer because the timing of document feeding is delayed.

Scanner Settings (Software Operation Panel)

281

«
...
279
280
281
282
283
...
»

Summary of Contents for fi-7300NX


































































































































































































































































































































Reviews:

No comments

Related manuals for fi-7300NX

DR 7090C - imageFORMULA - Document Scanner

Brand: Canon Pages: 2

Brand: FDI MATELEC Pages: 4

Brand: XINDAO Pages: 9

TECH-SCAN32 PLUS

Brand: Amdi Pages: 7

Brand: Uniden Pages: 84

D-LX 100 All-In-One

Brand: DURAG Pages: 36

Brand: Infinite Peripherals Pages: 26

Brand: Camlink Pages: 8

Brand: Radio Shack Pages: 14

Brand: P.Lindberg Pages: 30

Brand: Portronics Pages: 2

Brand: Opticon Pages: 2

LineScanner MP150

Brand: RayTek Pages: 60

Brand: Panasonic Pages: 61

PowerScan BC9620

Brand: Datalogic Pages: 38

Brand: Pandigital Pages: 2

Brand: Xerox Pages: 2

Brand: Sharp Shape Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands