Fujitsu fi-7300NX Operator'S Manual Download

Page: 161 / 321

Connection Test Result

●

"0% packet loss" shown in the test result

Meaning

The communication with the host specified in [Host Name/IP address] is normal.

●

"100% packet loss" shown in the test result

Meaning

Failed to communicate with the destination specified in [Host Name/IP address].

Solution

[Host Name/IP address] may not be specified correctly. Make sure that the host name or the IP address is
specified correctly.
If the problem persists, refer to the following section in

Troubleshooting (page 162)

●

The Connection Between the Scanner and Computer Frequently Cuts Off (page 183)

●

Cannot Connect the Scanner to a Destination by Specifying an IP Address (page 190)

●

Cannot Connect the Scanner to a Destination by Specifying a Host Name (page 192)

●

"99% packet loss" shown in the test result

Meaning

Communication with the destination specified in [Host Name/IP address] is unstable.

Solution

Refer to

Cannot Connect the Scanner and a Computer via Wi-Fi (page 169)

and

Cannot Connect the

Scanner and a Computer via a Wired LAN (page 184)

, and take measures accordingly.

●

"ping: bad address" shown in the test result

Meaning

The name-resolution or address-resolution for the destination specified in [Host Name/IP address] may
have failed.

Solution

●

Make sure that [Host Name/IP address] is specified correctly.

●

Make sure that the DNS server settings are correct.

●

If [Host Name/IP address] is specified correctly, refer to

Cannot Connect the Scanner to a Destination by

Specifying a Host Name (page 192)

for further solutions.

●

Refer to

Cannot Connect the Scanner and a Computer via Wi-Fi (page 169)

and

Cannot Connect the

Scanner and a Computer via a Wired LAN (page 184)

, and take measures accordingly.

Troubleshooting

161

Summary of Contents for fi-7300NX


































































































































































































































































































































Search results

Summary of Contents for fi-7300NX

Reviews:

Related manuals for fi-7300NX

Brands by name

Popular brands

Fujitsu fi-7300NX, Operator'S Manual

Search results

Summary of Contents for fi-7300NX

Reviews:

Related manuals for fi-7300NX

Brands by name

Popular brands