Fujitsu fi-7300NX Operator'S Manual Download Page 112 | Manualshive

Page: 112 / 321

background image

Disabling the Paper Protection Function

If you attempt to scan a wrinkled document with the paper protection function set to enabled, the scanner may
mistake it as a paper jam even though paper is fed normally, which causes paper protection to be performed
and forces a scan to be stopped. In this case, you can disable paper protection only for the protected document
to be scanned again.

Operational Procedure

1

When [Paper protection (feeding noise)] (error code: "J0:37") or [Paper protection (feeding accuracy)]
(error code: "J0:51") is displayed on the touch screen, open the ADF and remove the document.
For details, refer to

How to Open the ADF (page 63)

.

CAUTION

When the ADF is open, it might close accidentally. Be careful not to get your fingers
caught.

2

Close the ADF.
For details, refer to

How to Close the ADF (page 64)

CAUTION

Be careful not to get your fingers caught when closing the ADF.

ATTENTION

Confirm that the ADF is closed properly. Otherwise, documents may not be fed into the ADF.

3

Load the removed document back in the ADF paper chute (feeder).

4

Respond to a message that is displayed in the touch screen.
The following setting can be configured.

Disable the paper protection for the next document

Select whether to disable the paper protection to scan the protected document again.

5

Press the [Scan] button.
Starts scanning documents.
The paper protection function is disabled for the first sheet of documents. From the second sheet onwards,
the paper protection function is enabled.

HINT

If errors to protect documents are frequently displayed on the touch screen, refer to

Paper Protection Is Set Off

Frequently (page 207)

.

Various Ways to Scan

112

«
...
110
111
112
113
114
...
»

Summary of Contents for fi-7300NX


































































































































































































































































































































Reviews:

No comments

Related manuals for fi-7300NX

Brand: VALOI Pages: 56

Brand: Leuze Pages: 15

Brand: Panduit Pages: 7

Brand: Colortrac Pages: 92

Brand: R&S Pages: 17

PROFESSIONAL T8

Brand: ICON Pages: 28

Brand: Zurich Pages: 33

MindMi System MindSpring

Brand: Psychometric Systems Pages: 8

Brand: Pepperl+Fuchs Pages: 24

Scanner Compact

Brand: Raven Pages: 2

Brand: Zebex Pages: 4

Brand: caenrfid Pages: 12

Brand: Xerox Pages: 62

Brand: Faro Pages: 5

Brand: Radio Shack Pages: 56

S500M - ScanSnap - Document Scanner

Brand: Fujitsu Pages: 2

S1500 - ScanSnap Deluxe Bundle

Brand: Fujitsu Pages: 3

S500M - ScanSnap - Document Scanner

Brand: Fujitsu Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands