Fujitsu fi-7160 Operator'S Manual Download Page 192 | Manualshive

Page: 192 / 229

background image

Chapter 9 Operational Settings

192

How to Load
Documents

Configuring the
Scan Settings

How to Use the
Operator Panel

Various Ways to
Scan

Troubleshooting

Replacing the
Consumables

Scanner
Overview

Operational
Settings

Specifying the Sensitivity Level for Paper
Protection
[Paper Protection Sensitivity]

Specify the sensitivity level to detect anomalies upon feeding
the documents when paper protection is on.
Documents are deformed (e.g. warped, bent, creased) or
paper jam noise is made when documents are not being fed
by the rollers properly. To detect such a symptom and stop the
scan, select [Low] to only detect documents that are highly
deformed or paper jam noise that are loud. Select [High] to
also detect documents that are slightly deformed or small
paper jam noise.

1

Start up the Software Operation Panel.

For details, refer to

"9.1 Starting Up the Software Operation Panel"

2

From the listing on the left, select [Device Setting 2]
[Paper Protection Sensitivity].

HINT

z

If you scan a wrinkled document, paper protection may be set
off forcing a scan to be stopped even though paper is fed
normally. In this case, you can disable paper protection on the
operator panel for a single scan after paper protection is set off.
For details, refer to

"Disabling Paper Protection for a Single

Scan After Paper Protection Is Set Off" (page 106)

z

If paper protection is set off frequently, refer to

protection is set off frequently." (page 150)

.

z

This setting can also be configured in the scanner driver or the
operator panel. When the operation panel setting is prioritized,
the operator panel setting is prioritized over the Software
Operation Panel setting. Note that even if the operation panel
setting is prioritized, the scanner driver setting has the highest
priority.

«
...
190
191
192
193
194
...
»

Summary of Contents for fi-7160






































































































































































































































Reviews:

No comments

Related manuals for fi-7160

Brand: Symbol Pages: 6

Brand: QTS Pages: 66

Brand: Reflecta Pages: 40

Brand: jcm-tech Pages: 20

ONETOUCH 7400 USB

Brand: Visioneer Pages: 2

OneTouch 5300 Series

Brand: Visioneer Pages: 40

Brand: Roland Pages: 33

Brand: Scantech Pages: 49

SecureScan X100

Brand: Plustek Pages: 28

Brand: Plustek Pages: 38

Brand: Plustek Pages: 29

Brand: Plustek Pages: 78

SIMRAD StructureScan 3D

Brand: Lowrance Pages: 2

PANNORAMIC SCAN RX 1.1

Brand: 3DHISTECH Pages: 165

9238 - Super Coolscan 5000 ED

Brand: Nikon Pages: 81

SafeScan SG1004A

Brand: Safe-grain Pages: 2

Brand: Xerox Pages: 65

Brand: Kodak Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands