Fujitsu FI-5900C Operator'S Manual Download Page 88

Page: 88 / 257

3.1 Double Sided Scanning

3.1 Double Sided Scanning

When you want both sides of a document to be scanned at the same time, set the feeding option to
“Duplex”.

Below is the procedure with TWAIN driver.

Set the document on the hopper.

Refer to section

“2.6 Loading Documents on the Hopper” on page 17

Adjust stacker in accordance with document size.

Refer to section

“2.7 Setting up the Stacker” on page 22

Start TWAIN driver with the application used.

Refer to section

“2.13 How to use the Scanner Driver” on page 41

Set the [Scan Type:] to “ADF (Duplex)”.

Set resolution and document size and so on, and then click [Scan] button.

Summary of Contents for FI-5900C


































































































































































































































































Search results

Summary of Contents for FI-5900C

Reviews:

Brands by name

Popular brands

Fujitsu FI-5900C, Operator'S Manual

Search results

Summary of Contents for FI-5900C

Reviews:

Brands by name

Popular brands