manualshive.com logo in svg

Fujitsu FI-5900C, Operator'S Manual

Share
Download
Fujitsu FI-5900C Operator'S Manual Download Page 234

214

8.24 Imprinter Selection

8.24 Imprinter Selection

You can specify which imprinter to use; Pre-imprinter or Post-imprinter, if you already have installed these 
options.

Configure the settings for the Imprinter Selection as follows:

1.

Start up the Software Operation Panel.

Refer to 

“8.1 Scanner Settings” on page 177

.

2.

Select [Device Setting 2] from left side list in the window, and select 
[Imprinter selection] from its lower level.

3.

Select the Imprinter to use.

Normal (obey Host specification): Complies 

with 

the scanner driver setting.

Forcibly select Pre-imprinter:

Pre-imprinter is forcibly used to print unless directed by 

the scanner driver. 

Forcibly select Post-imprinter:

Post-imprinter is forcibly used to print unless directed by 

the scanner driver.

HINT

For details on the specifications of the imprinter, refer to 

“9 OPTIONS” on 

page 223

.

Summary of Contents for FI-5900C


































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands