Fujitsu ETERNUS AX Series Page 65 Manual Download | Manualshive

Page: 65 / 68

background image

2. Rack Installation Specifications
Installable Racks

Site Planning Guide

65

Non-Fujitsu Racks

The ETERNUS AX/HX storage systems are developed and their operation is guaranteed on the assumption that
they are installed in Fujitsu 19-inch racks. Since the ETERNUS AX/HX cannot be tested (for cooling and strength)
in non-Fujitsu 19-inch racks, the operations of ETERNUS AX/HX storage systems cannot be guaranteed. Any prob-
lem that may occur by installing the ETERNUS AX/HX in non-Fujitsu racks is not covered by the warranty.
If the ETERNUS AX/HX needs to be installed in a non-Fujitsu rack, the following conditions must be satisfied.

■

Rack Specifications

Use the rack mount kit supplied with the product to install the ETERNUS AX/HX in the rack. The rack specifications
must satisfy the conditions listed below. For rack specifications, refer to the manual for the rack that is used.

•

Pitch for mounting holes
EIA Standard Universal pitch

•

Size for mounting holes (for rack mount kits ordered before September 30, 2021)
Square hole: 9.5

±

0.1 mm (recommended)

Round hole: 7.1

±

0.1 mm (recommended)

•

Size for mounting holes (for rack mount kits ordered after October 1, 2021)

Table 30 Size for Mounting Holes (for Rack Mount Kits Ordered after October 1, 2021)

*1: Note that the size of the mounting holes on the drive shelves included in the basic configuration differs from that on

the optional drive shelves.

•

Load bearing capacity
The load bearing capacity must be equal to or larger than the total weight of the ETERNUS AX/HX.

•

Unit installation area
The dimensions of the area shown in

must match the conditions described in

.

Target

Model

Size for mounting holes

Basic

AX1100/AX2100
HX2100/HX2200

Square hole: 9 mm or more
Round hole: not supported

AX2200

Square hole: 9.5

±

0.1 mm

Round hole: 7.1

±

0.1 mm

AX4100
DS224C drive shelf (*1)
NS224 drive shelf
HX6100
DS212C drive shelf (*1)
DS224C drive shelf (*1)
DS460C drive shelf

Optional

DS212C drive shelf (*1)
DS224C drive shelf (*1)

Square hole: 9 mm or more
Round hole: not supported

DS460C drive shelf
NS224 drive shelf

Square hole: 9.5

±

0.1 mm

Round hole: 7.1

±

0.1 mm

«
...
63
64
65
66
67
...
»

Summary of Contents for ETERNUS AX Series





































































Reviews:

No comments

Related manuals for ETERNUS AX Series

Brand: Yardmaster Pages: 20

Brand: SanDisk Pages: 2

Brand: Décor et Jardin Pages: 24

Brand: LaCie Pages: 27

Brand: Gladiator Pages: 16

Brand: oldfields Treco Pages: 28

QuantaGrid D51PH-1ULH

Brand: QCT Pages: 167

Brand: Hama Pages: 8

Skylight Shed-6x3

Brand: Palram Pages: 35

Brand: HP Pages: 1

Brand: EDSLab Pages: 24

Brand: Trinity Pages: 12

Basics TLS-4820

Brand: Trinity Pages: 16

Brand: Edsal Pages: 2

Brand: EditShare Pages: 112

USB STORiUM N DRIVE

Brand: HANBiT Electronics Pages: 14

Brand: LaCie Pages: 54

Brand: Dedoes Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands