Fujitsu ETERNUS AF650 S2 Basic Operation Manual Download

Page: 46 / 59

Chapter 4

Process Time (Estimated)

This chapter explains the estimated time that is required for volume formatting and for rebuild/copyback for
each RAID level configuration.

4.1

Volume Formatting Time

The following table shows the time required for the volume formatting process.

Table 4.1 Volume Formatting Time

RAID level

Number of drives

Volume formatting time (*1)

SSDs

RAID1

2 (1D+1M)

Approx. 14 minutes/200GB

RAID1+0

4 (2D+2M)

Approx. 9 minutes/200GB

RAID5

5 (4D+1P)

Approx. 6 minutes/200GB

RAID5+0

8 ((3D+1P)

Approx. 6 minutes/200GB

RAID6

6 (4D+2P)

Approx. 7 minutes/200GB

*1: The value shows the time required for volume formatting when the volume capacity is 200GB and there

is no server I/O. The time that is required depends on the type and configuration of the drive.

FUJITSU Storage ETERNUS AF650 S2, ETERNUS AF650 All-Flash Arrays Operation Guide (Basic)

P3AG-1932-04ENZ0

Summary of Contents for ETERNUS AF650 S2




























































Search results

Summary of Contents for ETERNUS AF650 S2

Reviews:

Related manuals for ETERNUS AF650 S2

Brands by name

Popular brands

Fujitsu ETERNUS AF650 S2, Basic Operation Manual

Search results

Summary of Contents for ETERNUS AF650 S2

Reviews:

Related manuals for ETERNUS AF650 S2

Brands by name

Popular brands