En-3
OPERATING TIPS
Operation and Performance
About priority state and standby state
●
Multiple indoor units can be connected within the same system.
Depending on the system, choice of operating mode are limited.
Cooling priority state:
When the other indoor units within the same system operate in cooling
or dry mode, heating can not be selected at the same time.
Heating priority state:
When the other indoor units within the same system operate in heating
mode, cooling and dry mode can not be selected at the same time.
Standby state:
The standby state activates when 2 or more indoor units start up at the
same time in different mode. Any indoor unit other than priority mode
will wait in standby state until priority mode changes (operation starts
as soon as priority is switched).
At this time, the operation indicator lamp (green) lights up and the timer
indicator lamp (red)
fl
ashes.
Low ambient cooling
●
When the outdoor temperature drops, the outdoor unit’s fans may
switch to Low Speed, or one of the fans may stop intermittently.
Heating performance
●
Heating mode operates on the heat-pump principle, absorbing heat
from outdoor air and transferring that heat indoors. As a result, the
operating performance is reduced as outdoor air temperature drops.
If you feel that insuf
fi
cient heating performance is being produced, we
recommend you use this air conditioner in conjunction with another
type of heating appliance.
●
Heating mode heat your entire room by recirculating air throughout the
room, with the result that some time may be required after
fi
rst starting
the air conditioner until the room is heated.
Microcomputer-controlled automatic defrosting
●
When using the Heating mode under conditions of low outdoor air
temperature high humidity, frost may form on the outdoor unit, result-
ing in reduced operating performance. In order to prevent this kind of
reduced performance, this unit is equipped with a Microcomputer-con-
trolled automatic defrosting function. If frost forms, the air conditioner
will temporarily stop, and the defrosting circuit will operate brie
fl
y (for
about 4 to 15 minutes).
During Automatic Defrosting operation, the OPERATION indicator
lamp (green) will
fl
ash.
Oil recovery operation
●
Periodically, the oil recovery operation is performed in order to return
compressor oil to the outdoor unit.
During oil recovery operation, the OPERATION indicator lamp (green)
will
fl
ash (for about 10 minutes).
Temperature and humidity range
●
The temperature and humidity required for operating this product is as
shown in the following table.
Cooling/Dry Mode
Heating Mode
Outdoor
temperature
Please refer to the speci
fi
cation of outdoor units.
Indoor
temperature
18 to 32 °C DB
10 to 30 °C DB
Indoor humidity
About 80% or less
HUMAN SENSOR
(030/034 model only)
About the human sensor
The Human sensor detects whether there are people in the room by
looking for movement by people in the room.
Setting of Human sensor can be done in the remote controller of the fol-
lowing. Refer to the operating manual of the remote controller.
●
UTY-RNR*Z* (wired remote controller)
About the Auto saving operation
If no one enters the room during the set time (15, 30, 60, 90, 120, 180
minutes), the set temperature will be automatically controlled.
(When someone comes back into the room, the Human sensor will de-
tect this, and automatically revert to the original settings.)
About the Auto off operation
If no one enters the room during the set time (1 to 24 hours in 1 hour
increments), the air conditioner will automatically stop operation.
NOTES:
●
To restart operation, press the [On/Off] button of the remote controller.
●
The Auto off operation may not operate even if there is no one in the
room. The sensor may incorrectly detect people even if there is no one
in the room.
Application range
Vertical angle 90° (Side view)
Horizontal angle 100° (Top view)
90°
7 m
50°
50°
7 m
NOTES:
●
Energy Saving function may not work when the room temperature is
very different from the temperature de
fi
ned in temperature setting,
such as when immediately after starting the operation.
●
Since the Human sensor detects infrared light given out by people,
there may be cases where this detection is incorrect.
Situations in which the sensor will detect no people in the room,
even when there is someone there
●
When the temperature is high and the difference with between people’s
body temperature is small. (Such as during the summer when the
temperature is 30°C or higher.)
●
When there is someone in the room, but they do not move for a long
period of time.
●
When someone is hidden behind a sofa, other furniture, glass, or in
similar situations.
●
When someone is wearing extremely thick clothing and has their back
facing the sensor.
Situations in which the sensor will incorrectly detect people in the
room, even when there is no one there
●
When there is a dog or a cat moving around in the room.
●
When the wind is making curtains or plants move.
●
When there are heating units, humidi
fi
ers, or electric appliances such
as oscillating electric fans operating.
9377772398_OM.indb 3
9377772398_OM.indb 3
12/24/2018 4:42:37 PM
12/24/2018 4:42:37 PM
