manualshive.com logo in svg

Fujitsu ABHG18KRTA, Service Manual

Share
Download
Fujitsu ABHG18KRTA Service Manual Download Page 281

3-3. No operation (Power is on)

Forecast of cause

Setting/Connection failure

External cause

Electrical components defective

Check point 1. Check the indoor and outdoor installation condition

•

Indoor unit:

–

Check incorrect wiring between the indoor unit and remote controller.

–

Check if there is an open cable connection.

•

Are these indoor unit, outdoor unit, and remote controller suitable model names to connect?

-> If there is some abnormal condition, correct it by referring to the installation manual and “DESIGN
& TECHNICAL MANUAL”.

↓

Turn off the power and check correct followings.

•

Is there loose or removed communication line of indoor unit and outdoor unit?

↓

Check point 2. Check external cause at indoor and outdoor (Voltage drop or Noise)

•

Instant drop: Check if there is a large load electric apparatus in the same circuit.

•

Momentary power failure: Check if there is a defective contact or leak current in the power sup-
ply circuit.

•

Noise: Check if there is any equipment causing harmonic wave near electric line. (Neon bulb or
electric equipment that may cause harmonic wave)
Check the complete insulation of grounding.

↓

3-3. No operation (Power is on)

- (03-65) -

3. Troubleshooting without error code

TROUBLESHOOTING

TROUBLESHOOTING

Summary of Contents for ABHG18KRTA
























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands