manualshive.com logo in svg

Fujitsu ABHG18KRTA, Service Manual

Share
Download
Fujitsu ABHG18KRTA Service Manual Download Page 232

2-2. E: 11. Serial communication error (Serial forward transfer

error) (Indoor unit)

Indicator

Indoor unit

Operation indicator

1 time flash

Timer indicator

1 time flash

Economy indicator

Continuous flash

Error code

E: 11

Detective actuator

Indoor unit

Main PCB

When the outdoor unit cannot properly receive the serial
signal from indoor unit for 10 seconds or more.

Fan motor

Outdoor unit

Main PCB

Forecast of cause

Connection failure

External cause

Main PCB failure

Check point 1. Reset the power and operate

Does error indication show again?
→ If no, go to 

"Check point 1-2"

.

↓

Check point 2. Check connection

Check any loose or removed connection line of indoor unit and outdoor unit.
→ If there is an abnormal condition, correct it by referring to the installation manual or the “DESIGN
& TECHNICAL MANUAL”.
Check connection condition is control unit. (If there is loose connector, open cable or mis-wiring.)

↓

Check point 3. Check the voltage of power supply

Check the voltage of power supply
Check if AC 198 V (AC 220 V -10%) to AC 264 V (AC 240 V +10%) appears at
outdoor unit terminal L—N.

+

-

↓

2-2. E: 11. Serial communication error (Serial forward transfer error) (Indoor unit)

- (03-16) -

2. Troubleshooting with error code

TROUBLESHOOTING

TROUBLESHOOTING

Summary of Contents for ABHG18KRTA
























































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands