En-7
CAUTION
Install the Front panel and Intake grille securely. If installation is imperfect, the Front
panel or Intake grille may fall off and cause injury.
9.
REMOTE CONTROLLER INSTALLATION
CAUTION
• Check that the indoor unit correctly receives the signal from the remote controller,
then install the remote controller holder.
• Select the remote controller holder selection site by paying careful attention to the
following:
Avoid places in direct sunlight.
Select a place that will not be affected by the heat from a stove, etc.
9.1. Remote controller holder installation
• Install the remote controller a maximum distance of 22 ft. (7 m) from the remote control
receiver. However, when installing the remote controller, check that it operates correctly.
• Install the remote controller holder to a wall, pillar, etc. with the tapping screw.
Remote controller holder
fi
Remote controller
holder
(1) Set
(2) Push
Remote
controller
Tapping
screw
(small)
Remote controller mounting
10. OPTIONAL KIT INSTALLATION
This air conditioner can be connected with the following optional kits.
• Wired remote controller
• Simple remote controller
• External connect kit
10.1.
Before installing wired remote controller
• When you use wired remote controller, some functions may not be used.
Please use the recommended optional remote controller.
CAUTION
• Before installing, be sure to disconnect all power supply.
• Don’t touch the heat exchanger.
• During installing or removing operation, be sure not to have wire caught by parts or
draw it hard. Or it may result troubles to the air-conditioner.
• Avoid place in direct sunlight.
• Select place that will not be affected by the heat from a stove, etc
• Before setting up the optional kit, please con
fi
rm whether air-conditioner can receive
the signal.
• Do not connect the wired remote controller to the terminal for power supply.
• When connecting the wired remote controller with the indoor unit, use the connecting
cable (supplied with wired remote controller or simple remote controller).
• Recommended cable length of wired remote controller is 32 ft. (10 m). Make sure to
do insulate of connecting part when extended the cable.
10.2.
Remote controller cable modi
fi
cation
(1) Use a tool to cut off the terminal on the end of the remote controller cable, and then
remove the insulation from the cut end of the cable.
(2) Connect the remote controller cable and connecting cable.
(supplied with wired remote controller)
Important:
Be sure to insulate the connection between the wires.
Connecting cable
White
Red
White
Red
Black
Black
Insulated
connection
Remote
controller cable
Remote
controller cable
13/16 in. (20 mm)
Overlap the insulation
Vinyl tape
Wrap with cloth tape
Cloth tape
Drain hose
Connection cable
Pipe
Drain hose
Check the following:
GOOD
Drain hose
Saddle
Lifted up
Wave
End in water
Drain hose
Connection pipe
Wall pipe
Connection cable
Left piping
For connection from the left rear
Pipe
Connection pipe
(heat insulation)
Indoor unit pipe
(heat insulation)
PROHIBITED
Bind the pipes together
so that there is no gap.
8. FRONT PANEL REMOVAL AND INSTALLATION
8.1. Intake grille removal
(1) Open the intake grille.
(2) Pull down the knob.
(3) Lift the intake grille upward, until the axle at the top of the intake grille is removed.
8.2. Intake grille installation
(1) The
fi
xing axle of the intake grille is installed on the Panel.
(2) Lay down the intake grille.
8.3. Front panel removal
(1) Remove intake grille (Reference the intake grille removal.)
(2) Remove 6 screws.
(3) The thumb is hung on the lower part as shown in the
fi
gure, and it pulls to the front,
pushing [
▲
] mark , and bottom hooks (2 position) is removed from wall hook bracket.
(4) The front panel is pulled to the front, raising the upper surface, and a front panel is
removed.
8.4. Front panel installation
(1) First,
fi
t the lower part of the front panel, and insert top and bottom hooks. (3 top
sides)
(2) Attach the 6 screws.
(3) Attach the intake grille.
Top holes (two sides)
Top hole (center)
Top hook (center)
Front panel
Indoor unit
Top hooks
(2 sides)
Wall hook bracket
Front panel
Push
[
▲
] mark
Screws (6 position)
Push
Front panel
Front panel
Bearing
Mounting shaft
Intake grille
Intake grille
Knob
9318739183_IM.indb 7
9318739183_IM.indb 7
11/19/2014 6:04:32 PM
11/19/2014 6:04:32 PM
