Fujitsu 5900C - fi - Document Scanner Getting Started Download Page 4

ii

INTRODUCTION

Thank you for purchasing the fi-5900C Duplex Color 
Scanner. 
This document describes how to use fi-5900C and basic 
operation methods. Before you start using fi-5900C be 
sure to thoroughly read this manual to ensure correct 
use. 

The "Operator’s Guide" stored on the Setup CD-ROM 
provides useful and detailed information on Operations 
when you would like to use advanced features, Daily 
Care for maintenance of the scanner, and Replacing 
Consumables to maintain conditions for smooth scan-
ning. Please also read the Operator’s Guide for further 
information.

■ 

Regulatory Information

FCC declaration

This equipment has been tested and found to 

comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable 

protection against harmful interference in a 

residential installation. This equipment generates, 

uses, and can radiate radio frequency energy and, 

if not installed and used in accordance with the 

instruction manual, may cause harmful 

interference to radio communications. However, 

there is no guarantee that interference will not 

occur in a particular installation. If this equipment 

does cause harmful interference to radio or 

television reception, which can be determined by 

turning the equipment off and on, the user is 

encouraged to try to correct the interference by 

one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment 
and receiver.

Connect the equipment into an outlet on a circuit 
different from that to which the receiver is 

located.

Consult your dealer or an experienced radio/TV 
technician.

FCC warning:

 Changes or modifications not 

expressly approved by the party responsible for 

compliance could void the user’s authority to 

operate the equipment.

Canadian DOC Regulations

This digital apparatus does not exceed the Class B 

limit for radio noise emissions from digital 

apparatus set out in the Radio interference 

Regulations of the Canadian Department of 

Communications.

This Class B digital apparatus complies with 

Canadian ICES-003.

Le présent appareil numérique n'émet pas de 

parasites radioélectriques dépassant les limites 

applicables aux appareils numériques de la classe 

B et prescrites dans le Règlement sur le brouillage 

radioélectrique dictées par le Ministère des 

Communications du Canada.

Cet appareil numérique de la classe B est 

conforme à la norme NMB-003 du Canada.

Bescheimigung des Herstellers / 
Importeurs

Für den fi-5900C wird folgendes bescheinigt:

In Übereinsstimmung mit den Bestimmungen 
der EN45014(CE) funkentstört

Maschinenlärminformationsverordnung 
3.GPSGV: Der höchste Schalldruckpegel beträgt 

70 dB (A) oder weniger, gemäß EN ISO 7779.

International E

NERGY 

S

TAR

®

 Program

As an 

E

NERGY 

S

TAR

®

 

Partner, PFU LIMITED 

has determined that this 

product meets the 

E

NERGY 

S

TAR

®

 

guidelines for energy 

efficiency.

The International 

E

NERGY 

S

TAR

®

 Office 

Equipment Program is an international program 

that promotes energy saving through the 

penetration of energy efficient computers and 

other office equipment. The program backs the 

development and dissemination of products with 

functions that effectively reduce energy 

NOTICE

The use of a shielded interface cable 

is required to comply with the Class B 
limits of Part 15 of FCC rules. The 
length of the SCSI interface cable 
must be 1.5 meters (5 feet) or less..

The length of the AC cable must be 3 

meters (10 feet) or less.

Summary of Contents for 5900C - fi - Document Scanner































Reviews: