Fujitsu Siemens Computers PRIMERGY RX100 S4 User Manual Download Page 87

Page: 87 / 285

PRIMERGY RX100 S4 User’s Guide

allation

sing ServerS

Remote Installation Using a Remote Resource Server

In remote installation using a remote resource server, ServerStart starts up on the target server.

Procedures for starting installation are the same as those in normal installation (preparation, guided, and

expert modes). Once installation started, resources necessary for installation are provided from the

remote resource server. Thus, procedures such as inserting a CR-ROM are not necessary.

3.4.2 System Requirements for Remote Resource/PXE

Servers

Because remote installation is performed via a network, the environment must have at least one

Windows server and a local area network.

In addition, the following environment is required.

Remote Resource/PXE Server Requirements

Notes on the PXE server

Check that no other PXE server exists on the same LAN.

Servers installed with software with the PXE function such as the Microsoft RIS function cannot be

used as a PXE server.

table: System Requirements for Remote Resource/PXE Servers

Remote resource server

PXE server

Windows Server 2003

Windows 2000 Server

Windows 2000 Server SP2 to 4

Windows Server 2003

Memory

256MB or more

Operating
environment

• File sharing function (required)

• DHCP server function (required on the same network)
• File sharing function (required)

Target server

Remote resource server

Active ServerStart
and start installation

1) Request resources

Supply resources

- OS
- Service Pack
- Application
etc.

Summary of Contents for PRIMERGY RX100 S4






























































































































































































































































































Search results

Summary of Contents for PRIMERGY RX100 S4

Reviews:

Brands by name

Popular brands

Fujitsu Siemens Computers PRIMERGY RX100 S4, User Manual

Search results

Summary of Contents for PRIMERGY RX100 S4

Reviews:

Brands by name

Popular brands